FluoroGrip® – F (HD-FEP) Teflon® is a high-performance fluoropolymer coating that provides excellent non-stick properties, high chemical resistance, and durability under heat and mechanical stress. It’s ideal for industrial applications where clean release and corrosion protection are critical.
Use the links below to discover FluoroGrip® – F (HD-FEP) Teflon®
FluoroGrip® – F (HD-FEP) Teflon® is a high-performance fluoropolymer coating that provides excellent non-stick properties, high chemical resistance, and durability under heat and mechanical stress. It’s ideal for industrial applications where clean release and corrosion protection are critical.
FluoroGrip® – F fluoropolymer film is manufactured from high molecular weight fluorinated ethylene propylene (HD-FEP) resin by Integument Technologies, Inc.
FluoroGrip® – F is available standard with an advanced pressure sensitive adhesive (PSA) of acrylic or high temperature resistant silicone PSA. Special chemical resistant adhesives are available. Consult Integument Technologies for specific material recommendations.
FluoroGrip® – F is available with either a single-sided or doublesided surface plasma modification treatment.
FluoroGrip® – F film is made from high molecular weight resin for applications where chemical resistance, high flex life and stress-crack-resistant performance are required. Typical applications include tank and secondary containment linings, “splash-and-spill” paint replacement, acid brick and the membranes. The outstanding chemical and thermal resistance withstands aggressive environments, making it an excellent candidate for a wide variety of aggressive chemical and thermal environments. Fabricated shapes and contours can be produced via heat sealing and thermoforming. The outstanding weatherability and optical properties of FluoroGrip® – F film provides excellent performance in outdoor
atmospheric environments.
The non-stick surface, chemical resistance, and 300-450°F (depending upon adhesive) usage temperature make FluoroGrip® – F an ideal release film for internal linings and paint replacement where a “non-stick” surface is desirable such as silos, stock chests and food processing areas (walls, equipment, bulk powder handling equipment, chutes, etc.).
Single-side modification makes the material suitable as a 30-mil hot-air weldable lining when low surface energy is demanded. Double-sided treatment is especially useful when installations require seams, overlaps or the application of chemical resistant coatings or top toppings. The double-sided modification makes it an ideal material for pipe wraps and tapes and general purpose film. The modification also creates a superior surface for use as a chemical and temperature resistant underlayment or membrane where the application of chemical resistant toppings permits its use in traffic and secondary containment lining applications.
| ASTM Method | Metric Value | Metric Units | English Value | English Units | |
|---|---|---|---|---|---|
|
Specific Gravity |
D-792 |
2.12-2.17 |
|
2.12-2.17 |
|
|
Yield (1mil film) |
|
18 |
m2/kg |
90 |
ft2/lb |
|
Flammability |
UL-94 |
V-0 |
|
V-0 |
|
|
Water Absorption, 24hr |
|
<0.01 |
% |
<0.01 |
% |
|
Available Thicknesses (Film Only; Not Including Adhesive) |
2 mil, 5 mil, 10 mil, 20 mil, 30 mil |
| ASTM Method | Metric Value | Metric Units | English Value | English Units | |
|---|---|---|---|---|---|
|
Tensel Strength @ Break |
D-882 |
24 |
MPa |
3500 |
Psi |
|
Elongation @ Break |
D-882 |
300 |
% |
300 |
% |
|
Tensile Modulus |
D-882 |
480 |
MPa |
70000 |
Psi |
|
Initial Tear Strength, 1mil |
D-1004 |
2.2-2.7 |
N |
1.1-1.2 |
lb |
|
Initial Tear Strength, 2mil |
D-1004 |
4.9-5.3 |
N |
1.1-1.2 |
lb |
|
Propagating Tear
Strength, 1mil |
D-1922 |
1.4-1.5 |
N |
0.32-0.33 |
lb |
|
Propagating Tear
Strength, 2mil |
D-1922 |
2.4-2.7 |
N |
0.55-0.60 |
lb |
|
Fold Endurance (M.I.T) |
D-2176 |
10000 |
Cycles |
10000 |
Cycles |
| ASTM Method | Metric Value | Metric Units | English Value | English Units | |
|---|---|---|---|---|---|
|
Dielectric Strength, 1 mil |
D-149 |
240 |
kV/mm |
6000 |
V/mil |
|
Dielectric Constant, 1kHz |
D-150 |
2.1 |
|
2.1 |
|
|
Dissipation Factor, 1kHz |
D-150 |
0.0003 |
|
<0.0003 |
|
| ASTM Method | Metric Value | Metric Units | English Value | English Units | |
|---|---|---|---|---|---|
|
Melt Point |
D-3418 |
252-282 |
˚C |
485-540 |
˚F |
|
Continuous Service Temp.* |
|
A 163 | S 206 |
˚C |
A 325 | S 400 |
˚ F |
|
Specific Heat |
|
1172 |
J/(k•˚K) |
.28 |
Btu/(lb•˚F) |
|
Coefficient of Thermal Conductivity |
|
0.195 |
w/(m•˚K) |
1.35 |
Btu in/(hr• ft2•˚F) |
|
Coefficient of Linear Thermal Expansion |
D-696 |
9.9×10-5 |
mm/(mm•˚C) |
5.5×10-5 |
in/(in•˚F) |
|
Limiting Oxygen Index |
D-2863 |
95 |
% |
% |
| ASTM Method | Metric Value | Metric Units | English Value | English Units | |
|---|---|---|---|---|---|
|
Refractive Index |
D-542 |
1.341-1.347 |
|
1.341-1.347 |
|
|
Solar Transmission |
E-424 |
96 |
% |
96 |
% |
* A = Acrylic Adhesive S = Silicone Adhesive
Refer to FluoroGrip® installation manual and instruction guide for the use and installation of FluoroGrip® films, membranes and lining systems.
FluoroGrip® – F is designed to meet the requirements to comply with the FDA’s Register of Food Additive Regulations
Disclaimer The information printed herein is furnished free of charge and is based on technical data that Integument Technologies, Inc. believes to be reliable. It is intended for use by persons having technical skill, at their own discretion and risk. The handling precaution information contained herein is given with the understanding that those using it will satisfy themselves that their particular use conditions present no health or safety hazards. While the information contained herein is believed to be correct, Integument Technologies, Inc. makes no representation as to the accuracy of it. Since the conditions of product use are beyond our control, Integument Technologies, Inc. assumes no liability in connection with any use of this information. The evaluation of the product described herein under end-use conditions prior to specifications is essential. Nothing contained herein is to be taken as a license to operate under or as a recommendation to infringe any patents.
Warranty Integument Technologies, Inc. warrants that at the time of shipment, its products are free of
defects in material and workmanship. THERE IS NO OTHER EXPRESS WARRANTY SELLER HEREBY DISCLAIMS ALL IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR ANY PARTICULAR PURPOSE INDICATED BY BUYER TO SELLER. Seller’s sole obligation under this warranty shall be, upon prompt written notice by Buyer of any defect or defects, and inspection,
if required by Seller, to replace FOB Seller’s plant, or at Seller’s option to allow credit for any defective products expressly warranted herein against defects by Seller UPON PURCHASE OF SELLER’S PRODUCT(S), IT IS EXPRESSLY AGREED UPON BY BUYER THAT THIS REMEDY OF REPLACEMENT OR CREDIT, AT SELLER’S OPTION, IS BUYER’S EXCLUSIVE REMEDY UNDER THIS WARRANTY, IN NO EVENT SHALL SELLER BE LIABLE FOR CONSEQUENTIAL DAMAGES.
Tapes & Films engineered for performance and customized for you.
Let us assist you in recommending the appropriate products for your specific application.
Call Integument at (716) 873-1199 or email us at info@integument.com